Rheem R-410A Manual de usuario descargar pdf (Pagina 31)

SYSTEM CHARGE TROUBLESHOOTING

SUPERHEAT CALCULATION

1. Measure the suction pressure at the suction line service valve.

2. Convert the suction pressure to saturated temperature. See Table 6.

3. Measure the temperature of the suction line at the suction line service valve.

4. Compare the temperature of the suction line to the saturated temperature.

5. The difference between saturated temperature and suction line temperature is

the superheat. Superheat normal range 9° to 16°.

SUBCOOLING CALCULATION

1. Measure the liquid pressure at the liquid line service valve.

2. Convert the liquid line pressure to saturated temperature. See Table 6.

3. Measure the liquid line temperature at the liquid line service valve.

4. Compare the liquid line temperature to the saturated temperature.

5. The difference between saturated temperature and liquid line temperature is the

subcooling. Subcooling normal range 5° to 14°.

LOW VOLTAGE SOLENOID TROUBLESHOOTING

Recommended troubleshooting process

1. Begin diagnosis at the ICC:

Check for flashing codes at the ICC.

2. Check compressor amperage:

Operate the system and measure compressor amperage. Cycle the solenoid on

and off at ten plus second intervals by applying and removing the molded plug

(make certain the ICC is in 2nd stage; large C on the 7-segment LED). Wait five

seconds after power is applied via the molded plug before taking a reading. The

compressor amperage should go up or down at least 25 percent (a saturated

condensing temperature below 80°F may not produce as wide a change in

amperage).

3. Check the voltage supplied to the solenoid:

Remove the solenoid plug from the compressor. With the unit running and the

thermostat calling for Y2 (24VAC at the yellow/blue wire; large C on the 7-seg-

ment LED), test the voltage output at the plug with a DC voltmeter. The reading

should be 4 to 18 volts. If not, unplug the harness from the ICC harness and

check voltage at the pins of the ICC harness. The ICC will not power the sole-

noid if the compressor is not running or fault code 1 or 9 is active.

4. Check solenoid resistance:

Measure the solenoid resistance at the pins on the compressor. The resistance

should be 32 to 60 ohms depending on compressor temperature. If the coil resis-

tance is infinity, much lower than 32 ohms, or is grounded the compressor must

be replaced.

TABLE 7

AIR CONDITIONING SYSTEM TROUBLESHOOTING TIPS

AIR CONDITIONING SYSTEM

ROUBLESHOOTING TIPS

TABLE 6

TEMPERATURE PRESSURE CHART

TEMP R-410A

(Deg. F) PSIG

-150 —

-140 —

-130 —

-120 —

-110 —

-100 —

-90 —

80 —

-70 —

-60 0.4

-50 5.1

-40 10.9

-35 14.2

-30 17.9

-25 22.0

-20 26.4

-15 31.3

-10 36.5

-5 42.2

0 48.4

5 55.1

10 62.4

15 70.2

20 78.5

25 87.5

30 97.2

35 107.5

40 118.5

45 130.2

50 142.7

55 156.0

60 170.1

65 185.1

70 201.0

75 217.8

80 235.6

85 254.5

90 274.3

95 295.3

100 317.4

105 340.6

110 365.1

115 390.9

120 418.0

125 446.5

130 476.5

135 508.0

140 541.2

145 576.0

150 612.8

DISCHARGE SUCTION

SUPERHEAT SUBCOOLING

COMPRESSOR

PRESSURE PRESSURE AMPS

Overcharge High High Low High High

Undercharge Low Low High Low Low

Liquid Restriction (Drier) Low Low High High Low

Low Evaporator Airflow Low Low Low Low Low

Dirty Condenser High High Low Low High

Low Outside Ambient Temperature Low Low High High Low

Inefficient Compressor Low High High High Low

TXV Sensing Bulb Charge Lost Low Low High High Low

Poorly Insulated Sensing Bulb High High Low Low High

SYSTEM PROBLEM

INDICATORS

1 2 ... 26 27 28 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Rheem R-410A Manual de usuario Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Acondicionadores de aire del sistema de división Rheem R-410A